Daytime Running Lights menu not showing after proxi alignment

[yurko]

Hello,
Fiat Doblo 263 2013 with 1,3 mJet engine.
After Multiecuscan proxi alignment procedure, from body computer menu on dashboard, disappeared item that allows enable and disable DRL's...
Hove I can return it back? Very love this function.

[shpuncik]

check in MES folder FESLog file with proxi log and compare with current proxi.

[yurko]

PROXI Alignment Procedure Log:

Reading CAN configuration data ...
CAN CONFIGURATION DATA:
4B 00 00 04 00 00 00 00 4B 00 00 04 00 00 00 00 01 00 00 00 00 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
4B 00 00 04 00 00 00 00 09 00 00 04 00 00 00 00 4B 00 00 04 00 00 00 00 09 00 00 04 00 00 00 00 09 00 00 04 00 00 00 00
33 36 32 36 33 30 31 34 30 32 36 4F 55 54 50 55 54 2D 4A 49 54 20 12 01 23 4B 00 00 04 00 00 00 00 09 00 00 04 00 00 00 00 84 C0 53 07 7B 00 37 10 23 00 00 04 00 07 00 14 06 0D 05 3C 00 00 00 00 09 10 05 0C 01 00 00 00 19 00 00 00 00 11 02 25 00 00 11 00 00 00 00 06 00 00 00 00
Body Computer Node (BCM/NBC)
Engine Control Node (ECM/NCM)
Dashboard Node (IPC/NQS)
Brake System Node (ABS/BSM/NFR)
Airbag Node (NAB/ORC)
(Multiecuscan 4.7R1)
25.01.2021 12:51:34
Fiat Doblò (type 263) 1.3 Multijet 16V
CAN Setup / PROXI Alignment Procedure
--------------------------------------------------------------

Body Computer Node (BCM/NBC): EOL Ok
Engine Control Node (ECM/NCM): Ok
Dashboard Node (IPC/NQS): EOL Ok
Brake System Node (ABS/BSM/NFR): Ok
Airbag Node (NAB/ORC): EOL Ok

WARNING: This vehicle is properly configured. PROXI Alignment is not needed!
EXECUTING ADJUSTMENT...
Engine type
Old value: Gasoline
New value: Diesel
COMPLETED


EXECUTING ADJUSTMENT...
Engine type
Old value: Type 2/1.4 16V
New value: Type 3/1.3 Multijet
COMPLETED


EXECUTING ADJUSTMENT...
Cruise control (from 2009)
Old value: Disabled
New value: Enabled
COMPLETED


EXECUTING ADJUSTMENT...
Cruise control (from 2009)
Old value: Enabled
New value: Disabled
COMPLETED


EXECUTING ADJUSTMENT...
Display external temperature on dashboard
Old value: Disabled
New value: Enabled
COMPLETED


EXECUTING ADJUSTMENT...
PROXI ALIGNMENT PROCEDURE
Writing CAN configuration data ...
Writing to module: Body Computer Node (BCM/NBC) SUCCESS!
Writing to module: Dashboard Node (IPC/NQS) FAILED! - Timeout error
Writing to module: Airbag Node (NAB/ORC) SUCCESS!
FAILED TO EXECUTE
Dashboard Node (IPC/NQS) FAILED! - Timeout error

Whenever I try proxy alignment procedure, it ends up with a write error in Dashboard - Timeout error. It's normal? Why it happened?

[yurko]

This is before I try with Proxy alignment:
CAN CONFIGURATION DATA:
6B 00 00 04 00 00 00 00 4B 00 00 04 00 00 00 00 09 00 00 00 00 00 00 00 09 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
6B 00 00 04 00 00 00 00 09 00 00 04 00 00 00 00 4B 00 00 04 00 00 00 00 09 00 00 04 00 00 00 00 09 00 00 04 00 00 00 00
33 36 32 36 33 30 31 34 30 32 36 4F 55 54 50 55 54 2D 4A 49 54 20 12 01 23 6B 00 00 04 00 00 00 00 09 00 00 04 00 00 00 00 84 C0 73 07 7B 00 37 10 23 00 00 04 00 07 00 14 06 0D 05 3C 00 00 00 00 09 10 05 0C 01 00 00 00 19 00 00 00 00 11 02 25 00 00 11 00 00 00 00 06 00 00 00 00


This is last log that I have:
CAN CONFIGURATION DATA:
4B 00 00 04 00 00 00 00 4B 00 00 04 00 00 00 00 01 00 00 00 00 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
4B 00 00 04 00 00 00 00 09 00 00 04 00 00 00 00 4B 00 00 04 00 00 00 00 09 00 00 04 00 00 00 00 09 00 00 04 00 00 00 00
33 36 32 36 33 30 31 34 30 32 36 4F 55 54 50 55 54 2D 4A 49 54 20 12 01 23 4B 00 00 04 00 00 00 00 09 00 00 04 00 00 00 00 84 C0 53 07 7B 00 37 10 23 00 00 04 00 07 00 14 06 0D 05 3C 00 00 00 00 09 10 05 0C 01 00 00 00 19 00 00 00 00 11 02 25 00 00 11 00 00 00 00 06 00 00 00 00

After first attempt removed radio NRR. It's normal, because I was change it for Chinese Android multimedia.
In this first attempt I try to enable Cruise control after 2009, External temperature sensor and Stop&Start system. After this first proxy alignment, removed DRL control from dashboard menu.

After that, I tried to return the settings as it was, but unfortunately for DRL. All other functions work fine.

[yurko]

check in MES folder FESLog file with proxi log and compare with current proxi.

Ok.
The data is different.
Can I return data from log back?

[shpuncik]

check in MES folder FESLog file with proxi log and compare with current proxi.

Ok.
The data is different.
Can I return data from log back?

try byte 44 - change from 53 to 73

[yurko]

try byte 44 - change from 53 to 73

Where I can do it?
Thanks you.

[yurko]

try byte 44 - change from 53 to 73

I was fount information how I can changes bytes in the proxy configuration procedure.
Byte 44 about Rear fog lights. 53 is rear fog lights set to only left and 73 set both fog lights.
What other bytes can I try to change for enable Daytime Running Light menu?

[yurko]

Daytime Running Lights menu disappearing is Multiecuscan proxi alignment bug.
Fix it with Alfa OBD.
If anyone is interested what codes I currently have in proxi alignment - let me know.

[ahmedhossam]

Daytime Running Lights menu disappearing is Multiecuscan proxi alignment bug.
Fix it with Alfa OBD.
If anyone is interested what codes I currently have in proxi alignment - let me know.

kindly i need the code and kindly let me know what is alfa OBD.
i need to activate the drl control on/off