Page 1 of 1

cantiecar with windows 10

Posted: 22 Nov 2018, 23:15
by yoko
Hi all,
I have got a new pc with windows 10 and i have cantiecar v4 interface
it works perfectly with windows 7 but with windows 10 i can't connect to some modules
after investigation i found when i test the cable on windows 7 i have no errors but in windows 10 i get a lot of errors like below

Code: Select all

CR:Copyright (C) 2005-2018 tieCAR.net Company ::.
ID:CANtieCAR:tieCAR.net Company ::.
SN:WTCWMJ21
BW:4.1.846
HW:4.3
FW:4.1.428
PT:2.6.1204
PW:ON
UP:02
UB:0.390V
PI:ON
UI:4.786V
U8:0.000V
PA:5V
UA:4.786V
Selected Mode: FES - MultiECUScan (FiatECUScan v3.4+)
--------------------------------
MCU:AT91SAM7X512
Test MCU pins:..
 82(A01) - Shorted to  21(A13)
 82(A01) - Shorted to  24(A16)
 82(A01) - Shorted to  26(A18)
 ....
 89(A05) - Shorted to  24(A16)
 89(A05) - Shorted to  26(A18)
 .........
 22(A14) - Shorted to  24(A16)
 22(A14) - Shorted to  26(A18)
 ....
 26(A18) - Shorted to  21(A13)
 ...
 49(A21) - Shorted to  24(A16)
 49(A21) - Shorted to  26(A18)
 ...
 56(A24) - Shorted to  24(A16)
 56(A24) - Shorted to  26(A18)
 .......
 40(B00) - Shorted to  21(A13)
 40(B00) - Shorted to  26(A18)
 ....
 54(B04) - Shorted to  24(A16)
 54(B04) - Shorted to  26(A18)
 .
 34(B05) - Shorted to  21(A13)
 34(B05) - Shorted to  24(A16)
 34(B05) - Shorted to  26(A18)
 ..
 38(B07) - Shorted to  24(A16)
 38(B07) - Shorted to  26(A18)
 ..
 27(B09) - Shorted to  24(A16)
 27(B09) - Shorted to  26(A18)
 .....
 29(B14) - Shorted to  24(A16)
 29(B14) - Shorted to  26(A18)
 .........
 69(B23) - Shorted to  24(A16)
 69(B23) - Shorted to  26(A18)
 .....
 10(B28) - Shorted to  26(A18)
 .. = ERRORs: 28
--------------------------------
Rates:
K	: 1417 kbit/s
L	: 1417 kbit/s
K8	: 1413 kbit/s
K-High	: 1417 kbit/s
K-Low	: 1413 kbit/s
CAN	: 716 kbit/s
FT_CAN	: 1093 kbit/s
H-High	: 1099 kbit/s
H-Low	: 1413 kbit/s
SW_CAN	: 1091 kbit/s
--------------------------------
Bluetooth: ..............................hc01.comV2.0 = Present
--------------------------------
WiFi: ..................ESP8266EX 512KB 2C:3A:E8:1D:1C:BB  = Present
--------------------------------
ADC and POWER Switches:
U_01	: 0.000V	- TEST: 4.786V
U_08	: 0.000V	- TEST: 4.750V
U_09	: 0.000V	- TEST: 4.750V
U_16	: 0.248V
--------------------------------
SW_ISO	SW_ADJ	: U_ISO	U_ADJ	U_LOW	U_HIGH
OFF	OFF	: 4.786	4.786	4.750	4.750
ON	OFF	: 4.786	4.786	4.786	4.786
OFF	ON	: 4.786	4.786	4.750	4.786
ON	ON	: 4.786	4.786	4.786	4.786
--------------------------------
DC-DC:
Skiped - Apply External Power to device and run test again
--------------------------------

RESULT : Error


what could be the problem?

Re: cantiecar with windows 10

Posted: 03 Dec 2018, 07:44
by yoko
any reply is appreciated