MES3.5 and Jeep Renegade 1.6JTD

General messages
Post Reply
fmodafferi
Posts: 7
Joined: 17 Mar 2017, 11:42
Location: Lamezia Terme [Italy]

MES3.5 and Jeep Renegade 1.6JTD

Post by fmodafferi » 17 Mar 2017, 14:23

Hi guys,

today, I received my ELM327 v1.4 cable and I purchased MES3.5 in order to interact with my vehicle. I correctly conected the application to my car and I fully connected to various ECUs. But I received an error trying to proceed to the Proxy alignment zone: MES reported that the connection was unreliable. The MES portal reports that there is no need of "special cable" to proceed to the alignment but only the same ELM327 is enough. Any clue on this issue?

Ps: During the cable test, there is an overall "OK" with a warning on a too high latency...
°|||||||°
Jeep Renegade MY16
1.6JTDm Limited

s130
Posts: 941
Joined: 20 Jan 2010, 10:07
Location: Wrexham, North Wales

Re: MES3.5 and Jeep Renegade 1.6JTD

Post by s130 » 17 Mar 2017, 14:37

This is a known issue with R3.5 for both the 500X and Renegade.

MES Development have developed a fix which should be available in the next release.
Fiat Strada/Ritmo Abarth 130TC, Barchetta 2005 , 500X Cross Plus

fmodafferi
Posts: 7
Joined: 17 Mar 2017, 11:42
Location: Lamezia Terme [Italy]

Re: MES3.5 and Jeep Renegade 1.6JTD

Post by fmodafferi » 17 Mar 2017, 15:01

s130 wrote:This is a known issue with R3.5 for both the 500X and Renegade.

MES Development have developed a fix which should be available in the next release.

Good news, waiting for this fix, hoping to have it asap... ;)
°|||||||°
Jeep Renegade MY16
1.6JTDm Limited

fmodafferi
Posts: 7
Joined: 17 Mar 2017, 11:42
Location: Lamezia Terme [Italy]

Re: MES3.5 and Jeep Renegade 1.6JTD

Post by fmodafferi » 31 May 2017, 06:04

Is there any news on the issue of the proxy on Renegade and 500X? Has the problem been fixed on MES 3.6?
°|||||||°
Jeep Renegade MY16
1.6JTDm Limited

yani
Site Admin
Posts: 1175
Joined: 06 Nov 2009, 16:40

Re: MES3.5 and Jeep Renegade 1.6JTD

Post by yani » 31 May 2017, 17:38

Yes, everything works correct in Multiecuscan 3.6. You have to configure the interface as "ELM 327 1.3/1.4/1.4b/2.1 (High Speed)" in Multiecuscan.

fmodafferi
Posts: 7
Joined: 17 Mar 2017, 11:42
Location: Lamezia Terme [Italy]

Re: MES3.5 and Jeep Renegade 1.6JTD

Post by fmodafferi » 05 Jun 2017, 07:46

Great news! Thank you!!
°|||||||°
Jeep Renegade MY16
1.6JTDm Limited

fmodafferi
Posts: 7
Joined: 17 Mar 2017, 11:42
Location: Lamezia Terme [Italy]

Re: MES3.5 and Jeep Renegade 1.6JTD

Post by fmodafferi » 08 Jun 2017, 14:29

Today I've tryied to align my proxy but it asked me to use all the adapter cables (A5 and A6). In the guide there's reported that the alignment is feasible just with the ELM cable... Is an error of the compatibility list or is an issue of the software?
°|||||||°
Jeep Renegade MY16
1.6JTDm Limited

Post Reply