Page 1 of 1

fia500

Posted: 07 Jun 2016, 15:36
by yuko1
Reading CAN configuration data ...
CAN CONFIGURATION DATA:
6F 84 00 04 02 00 00 00 6F 84 00 04 02 00 00 00 43 04 00 00 00 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
6F 84 00 04 02 00 00 00 09 00 00 04 02 00 00 00 6F 84 00 04 02 00 00 00 09 00 00 04 02 00 00 00 09 00 00 00 02 00 00 00
33 32 31 35 30 30 31 31 36 37 31 4F 55 54 50 55 54 2D 4A 49 54 20 14 07 31 6F 84 00 04 02 00 00 00 09 00 00 04 02 00 00 00 93 C2 75 06 F4 00 1C A0 AA 80 00 26 00 01 00 94 06 01 01 00 00 00 80 10 3A 41 0A 0C 0D 00 80 00 23 00 00 00 00 31 05 61 00 00 00 04 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80 00 11
Body Computer Node (NBC)
Engine Control Node (NCM)
Electric Steering Node (NGE)
Dashboard Node (NQS)
Receiver Radio (NRR)
Brake System Node (NFR)
Climate Control Node (NCL)
Side Acceler./Yaw Node (NYL)
Airbag Node (NAB)
Convergence Telematic Node (CTM)
6/7/2016 4:31:22 PM
CONNECTED TO:
Fiat 500 0.9 Turbo TwinAir
CAN Setup / PROXI Alignment Procedure
--------------------------------------------------------------

Body Computer Node (NBC): EOL Ok
Engine Control Node (NCM): Ok
Electric Steering Node (NGE): Ok
Dashboard Node (NQS): EOL Ok
Receiver Radio (NRR): Ok
Brake System Node (NFR): Ok
Climate Control Node (NCL): Ok
Side Acceler./Yaw Node (NYL): Ok
Airbag Node (NAB): EOL Failed
Convergence Telematic Node (CTM): EOL Ok

EXECUTING ADJUSTMENT...
Auxiliary audio input
Old value: Not enabled
New value: Enabled
COMPLETED


EXECUTING ADJUSTMENT...
Rear fog lights
EXECUTING ADJUSTMENT...
Driver's side
EXECUTING ADJUSTMENT...
Engine type
EXECUTING ADJUSTMENT...
Knee guard (driver's side)
Old value: Not Present
New value: Present
COMPLETED


EXECUTING ADJUSTMENT...
PROXI ALIGNMENT PROCEDURE
Writing CAN configuration data ...
Writing to module: Body Computer Node (NBC) SUCCESS!
Writing to module: Dashboard Node (NQS) SUCCESS!
Writing to module: Airbag Node (NAB) FAILED! - Request out of range error
Writing to module: Convergence Telematic Node (CTM) SUCCESS!
FAILED TO EXECUTE
Airbag Node (NAB) FAILED! - Request out of range error

-----------------------
how configure airbag?

Re: fia500

Posted: 23 Jan 2018, 11:40
by ion
hello,

i have the same problem here, i think the airbag was replaced and the product number is different. if you have any solution now please reply.

Re: fia500

Posted: 10 Feb 2018, 13:00
by alex-et3
ion wrote:hello,

i have the same problem here, i think the airbag was replaced and the product number is different. if you have any solution now please reply.
You have to buy the correct airbag control unit for your car