Body Computer Node (BCM/NBC) FAILED! - Request out of range error

[bully]

I am trying to disable the start/stop on a 2012 1.4 Multiair Giulietta.
When I try to do the Proxy alignment after changing the Stop/start function to not present I get this error. Body Computer Node (BCM/NBC) FAILED! - Request out of range error.
Here is the log file, can anyone help please?

Reading CAN configuration data ...
CAN CONFIGURATION DATA:
6F 04 00 05 00 00 00 00 6F 04 00 05 00 00 00 00 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
6F 04 00 05 00 00 00 00 09 04 00 04 00 00 00 00 6F 04 00 05 00 00 00 00 09 04 00 04 00 00 00 00 09 04 00 04 00 00 00 00
30 34 31 39 31 30 30 38 33 31 31 4F 55 54 50 55 54 2D 4A 49 54 20 11 07 14 6F 04 00 05 00 00 00 00 09 04 00 04 00 00 00 00 97 C5 51 07 8F 00 3C 11 38 00 00 1E 00 07 07 94 06 2D 03 3C 00 00 01 00 3A 51 0A 7C 00 00 00 00 09 00 00 00 00 37 11 61 01 38 00 20 00 00 00 04 06 00 00 00
Body Computer Node (BCM/NBC)
Engine Control Node (ECM/NCM)
Electric Steering Node (EPS/NGE)
Dashboard Node (IPC/NQS)
Receiver Radio (NRR)
Brake System Node (ABS/BSM/NFR)
Climate Control Node (HVAC/NCL)
Parking Sensor Node (PAM/NSP)
Airbag Node (NAB/ORC)
(Multiecuscan 5.2)
23/05/2024 11:59:08 pm
Alfa Romeo Giulietta 1.4 Turbo 16V
CAN Setup / PROXI Alignment Procedure
--------------------------------------------------------------

Body Computer Node (BCM/NBC): EOL Ok
Engine Control Node (ECM/NCM): Ok
Electric Steering Node (EPS/NGE): Ok
Dashboard Node (IPC/NQS): EOL Ok
Receiver Radio (NRR): Ok
Brake System Node (ABS/BSM/NFR): Ok
Climate Control Node (HVAC/NCL): EOL Ok
Parking Sensor Node (PAM/NSP): Ok
Airbag Node (NAB/ORC): EOL Ok

WARNING: This vehicle is properly configured. PROXI Alignment is not needed!
EXECUTING ADJUSTMENT...
STOP&START function
Old value: Present
New value: Not Present
COMPLETED


EXECUTING ADJUSTMENT...
PROXI ALIGNMENT PROCEDURE
Writing CAN configuration data ...
Writing to module: Body Computer Node (BCM/NBC) FAILED! - Request out of range error
[102A] errors: Byte 64: 01->0E
Writing to module: Dashboard Node (IPC/NQS) SUCCESS!
Writing to module: Climate Control Node (HVAC/NCL) SUCCESS!
Writing to module: Airbag Node (NAB/ORC) SUCCESS!
FAILED TO EXECUTE
Body Computer Node (BCM/NBC) FAILED! - Request out of range error

EXECUTING ADJUSTMENT...
PROXI ALIGNMENT PROCEDURE
Writing CAN configuration data ...
Writing to module: Body Computer Node (BCM/NBC) FAILED! - Request out of range error
[102A] errors: Byte 64: 01->0E
Writing to module: Dashboard Node (IPC/NQS) SUCCESS!
Writing to module: Climate Control Node (HVAC/NCL) SUCCESS!
Writing to module: Airbag Node (NAB/ORC) SUCCESS!
FAILED TO EXECUTE
Body Computer Node (BCM/NBC) FAILED! - Request out of range error

EXECUTING ADJUSTMENT...
PROXI ALIGNMENT PROCEDURE
Writing CAN configuration data ...
Writing to module: Body Computer Node (BCM/NBC) FAILED! - Request out of range error
[102A] errors: Byte 64: 01->0E
Writing to module: Dashboard Node (IPC/NQS) SUCCESS!
Writing to module: Climate Control Node (HVAC/NCL) SUCCESS!
Writing to module: Airbag Node (NAB/ORC) SUCCESS!
FAILED TO EXECUTE
Body Computer Node (BCM/NBC) FAILED! - Request out of range error

[abarthmultijet]

Don't know for sure, but i think it is not possible to disable stop/start via the proxy configuration.

You can go to an ecu tuner and disable start/stop in the engine ecu.

[s130]

There may be a away to do this.

Start/Stop even if enabled will not engage for a multitude of reasons in normal operation.

One such reason is the vehicles view of battery charge, not based on voltage but based on current in/out. To do this there is a very low resistance sensor in the negative terminal and the battery post. The vehicle monitors the very small voltages over time across this resistance. If you disconnect the sensor wire (easy to do on a 500X) then the system will initially reset and Start/Stop will work for a short while then eventually it will turn off as the system cannot determine the battery charge state.

Worth a try.