FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)

multiecuscan program usage help
Bumb
Posts: 7
Joined: 24 Mar 2017, 06:07

Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)

Post by Bumb » 24 Mar 2017, 06:17

Hello i bought elm 327 1.5a and i first i thought is the driver problems i didn't know unless i saw this thread.

I cant pass the last test on Multiecuscan v3.1.

U can see the problem is it in the second picture

I tried with different ports speeds and its fails in the first test.

Also when i connect to the car its says also that operation has timedout and check ports and cable...

Doi have to remove the resistor ?
Attachments
IMG_1124.PNG
IMG_1124.PNG (30.61 KiB) Viewed 5448 times
IMG_1123.PNG
IMG_1123.PNG (50.39 KiB) Viewed 5448 times
IMG_1122.PNG
IMG_1122.PNG (16.75 KiB) Viewed 5448 times

magic_fingers
Posts: 1
Joined: 02 Apr 2017, 08:39

Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)

Post by magic_fingers » 02 Apr 2017, 08:44

Can anybody help me identify the wrong resistor on my adapter board? I'm having trouble with it.
Car is an alfa 159 1.9jtdm 150
20170402_103807.jpg
20170402_103807.jpg (2.6 MiB) Viewed 5416 times
20170402_103744.jpg
20170402_103744.jpg (2.55 MiB) Viewed 5416 times

cxem
Posts: 28
Joined: 24 Jan 2015, 09:10
Location: Russia, Syktyvkar

Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)

Post by cxem » 03 Apr 2017, 01:53

Multiecuscan
CAN pin 6 and pin 14
Remove resistor 120 ohm
Video:
https://www.youtube.com/watch?v=emzyE-zkGmw

Perfezionista
Posts: 3
Joined: 03 Apr 2017, 17:52

Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)

Post by Perfezionista » 03 Apr 2017, 18:01

Alfaeddy wrote:...

Hello

This one

http://www.ebay.de/itm/152303739535?_tr ... EBIDX%3AIT

Greetings Eddy
Hello, I bought it on your recommendation and I am unsure with the functionality. We tried to use the interface on our 2008 Fiat Bravo 1.4 T-jet. If the interface is plugged in, all warning lights on the dashboard are ON and the engine coolant temperature gauge does not show - remains at start position. If it is not connected, everything is normal, lights go off after a few seconds and the temperature gauge moves to the corresponding position.

Is the interface ok? It is our first FIAT..

Thank you

Perfezionista
Posts: 3
Joined: 03 Apr 2017, 17:52

Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)

Post by Perfezionista » 05 Apr 2017, 20:01

I played with an old KL interface little bit and found out the AutoDia E327 interface has defective the FT-CAN (pins 2+10). It somehow cripples CAN bus of the car so ECUs store errors of the CAN. Supplier KWP2000 (ebay diadig) have not responded so far, so I cannot recommend purchasing it. So if you connect the interface to your car and all lights are on, do not go off, the interface is not good.
https://ibb.co/ijuybF

Alfaeddy
Posts: 1350
Joined: 19 Feb 2011, 17:43
Location: Germany , Aarbergen

Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)

Post by Alfaeddy » 05 Apr 2017, 21:29

Hello

I would not say that an interface is synonymous mal mal !!
But I know some who bought this ELM and have no problems with it.

Otherwise one should buy the OBDkey interface or here the complete package
With the CANtie Interface !! At a completely different price


At pin 2 + 10 is not a bus or is your Fiat not from Europe ??
Since these pins are used for the SAE1850 protocol.


If your interface is broken you can return it.

Greeting Eddy

Perfezionista
Posts: 3
Joined: 03 Apr 2017, 17:52

Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)

Post by Perfezionista » 06 Apr 2017, 17:14

Alfaeddy wrote:Hello

I would not say that an interface is synonymous mal mal !!
But I know some who bought this ELM and have no problems with it.

Otherwise one should buy the OBDkey interface or here the complete package
With the CANtie Interface !! At a completely different price


At pin 2 + 10 is not a bus or is your Fiat not from Europe ??
Since these pins are used for the SAE1850 protocol.


If your interface is broken you can return it.

Greeting Eddy
Hello Eddy, thanks for response. The interface has connected pins 2 and 10, which according to http://marco.guardigli.it/2010/10/hacking-your-car.html provide FT-CAN (probably B-CAN?, also http://www.alfaobd.com/AlfaOBD_Android_Help.pdf mentions Bus). It confirms errors related to CANBUS if it is connected. You are right Interface is cheap, so it is easier to disconnect these pins inside.

Alfaeddy
Posts: 1350
Joined: 19 Feb 2011, 17:43
Location: Germany , Aarbergen

Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)

Post by Alfaeddy » 10 Apr 2017, 11:37

Hello

I can unfortunately not follow your information? ;)

Again, PIN 2 + 10 is not the B-Can
This is at Pin 1 + 9


Pin 2 + 10 is for another protocol (SAE 1850)

I have written this here

Greeting Eddy

gurava
Posts: 1
Joined: 11 Apr 2017, 14:34

Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)

Post by gurava » 11 Apr 2017, 14:43

Hello!
my avto is Fiat Panda 2007 year 1.2
adapter is usb elm327 (ftdi chip) with fiatecuscan program
I can see only engine and Gearbox selespeed cfc 228f
Can anybody help me - where is resistor that must be dissassembled?
Attachments
IMG_20170411_161453.jpg
IMG_20170411_161453.jpg (1.34 MiB) Viewed 4785 times
IMG_20170411_161537.jpg
IMG_20170411_161537.jpg (1.34 MiB) Viewed 4785 times

cxem
Posts: 28
Joined: 24 Jan 2015, 09:10
Location: Russia, Syktyvkar

Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)

Post by cxem » 12 Apr 2017, 12:32

Here are:
121.png
121.png (810.67 KiB) Viewed 5126 times

Post Reply