multiecuscan program usage help
-
Alfaeddy
- Posts: 1350
- Joined: 19 Feb 2011, 17:43
- Location: Germany , Aarbergen
Post
by Alfaeddy » 02 Mar 2017, 19:57
anonimo76 wrote:
I have to connect to alfa mito 1.6 jtdm
Thanks
Hello
Nice that it now works
What interface did you buy?
Do you have a link?
Greeting Eddy
-
mrnixdorf
- Posts: 3
- Joined: 03 Mar 2017, 03:19
Post
by mrnixdorf » 03 Mar 2017, 03:45
hey guys,
any help with this interface i will appreciate it, i can only connect to ecu engine.
Thx
-
Alfaeddy
- Posts: 1350
- Joined: 19 Feb 2011, 17:43
- Location: Germany , Aarbergen
Post
by Alfaeddy » 04 Mar 2017, 00:45
mrnixdorf wrote:hey guys,
any help with this interface i will appreciate it, i can only connect to ecu engine.
Thx
Hello
And always the same questions !!!!
What vehicle?
What year?
What control?
What driver was installed?
Since the resistor only interferes with CAN bus protocols with multiecuscan.
Ergo:
No CAN bus
no problem
Greeting Eddy
-
mrnixdorf
- Posts: 3
- Joined: 03 Mar 2017, 03:19
Post
by mrnixdorf » 04 Mar 2017, 16:24
Alfaeddy wrote:mrnixdorf wrote:hey guys,
any help with this interface i will appreciate it, i can only connect to ecu engine.
Thx
Hello
And always the same questions !!!!
What vehicle?
What year?
What control?
What driver was installed?
Since the resistor only interferes with CAN bus protocols with multiecuscan.
Ergo:
No CAN bus
no problem
Greeting Eddy
What vehicle? Peugeot 307 HDI 1.6 110cv
What year? 2006
What control? i think VAN
What driver was installed? Bluethoot "Torque"
I don't understand but it must work with all vehicles, right?
-
anonimo76
- Posts: 15
- Joined: 01 Dec 2013, 23:06
Post
by anonimo76 » 04 Mar 2017, 17:59
anonimo76 wrote:Alfaeddy wrote:anonimo76 wrote:
I have to connect to alfa mito 1.6 jtdm
Thanks
Hello
Nice that it now works
What interface did you buy?
Do you have a link?
Greeting Eddy
hello, elm v. 1.5
I have to remove r2?
https://it.aliexpress.com/item/2016-Low ... 0.0.LeiDDO
Hi, I removed the resistor r2.
The interface test is okay.
But it does not connect with multiecuscan 3.0.
With Alfaobd connects to the service, to all the functions.
What's the problem?
-
Alfaeddy
- Posts: 1350
- Joined: 19 Feb 2011, 17:43
- Location: Germany , Aarbergen
Post
by Alfaeddy » 04 Mar 2017, 23:22
anonimo76 wrote:
Hi, I removed the resistor r2.
The interface test is okay.
But it does not connect with multiecuscan 3.0.
With Alfaobd connects to the service, to all the functions.
What's the problem?
Hello
I thought your ELM now works after removing R2.
Apparently, I read, translated wrongly
If you can connect with AlfaOBD yes there must be a software problem. ?? !!!
What driver did you install?
-
anonimo76
- Posts: 15
- Joined: 01 Dec 2013, 23:06
Post
by anonimo76 » 05 Mar 2017, 07:52
drivers installed properly with Windows XP "usb340T drivers", "CH341SER", provided with the CD.
After I removed the resistance, Alfaobd connects to the service, to all the services.
Multiecuscan anything, it does not connect to the ECU, but the interface test is all ok