FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)

multiecuscan program usage help
aaa456
Posts: 6
Joined: 28 Jul 2013, 18:41

Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)

Post by aaa456 » 03 Aug 2013, 09:46

Hi Alfaeddy,

well, that's the problem. Look at the first picture below.

Is this pin marking correct?:
OBDConn.jpg
OBDConn.jpg (70.17 KiB) Viewed 4691 times
And this is my adapter (PINs are marked as on picture above):
IMG_20130803_112507_mod.jpg
IMG_20130803_112507_mod.jpg (47.16 KiB) Viewed 4691 times
Is this correct pin-out?

Thanks.

M.

Alfaeddy
Posts: 1350
Joined: 19 Feb 2011, 17:43
Location: Germany , Aarbergen

Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)

Post by Alfaeddy » 03 Aug 2013, 11:11

Hello aaa456


The adapter (2nd picture) must go to the pin 1 on the connector pin 6 of the female connector
And pin 9 of the connector going to the pin 14 of the female connector

Is this so? on your adapter?

Your labeling of the pins is correct

Look again at the picture

Greetings Eddy

A3.jpg
A3.jpg (26.44 KiB) Viewed 4688 times

Alfaeddy
Posts: 1350
Joined: 19 Feb 2011, 17:43
Location: Germany , Aarbergen

Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)

Post by Alfaeddy » 03 Aug 2013, 11:18

Hello aaa456

Your image here have once more shown how the CAN bus must be Connections

Greetings Eddy
Adapter A3.jpg
Adapter A3.jpg (30.99 KiB) Viewed 4688 times

aaa456
Posts: 6
Joined: 28 Jul 2013, 18:41

Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)

Post by aaa456 » 04 Aug 2013, 08:29

Hi Alfaeddy,

yes, that's how it is connected. I was wrong, adapter is connected correctly (I was probably looking on it upside down :oops: ). Except one difference. According the scheme pins 4 and 5 should be connected together (short-circuit) but in my adapter they are just connected 4-4 and 5-5 (and not between pins). But maybe this is not a problem ...

So I really don't know where could be a problem ... :-( It's true that ELM interface connected directly to OBD in car is tighter than adapter (very loose). I tried to push it and hold it while I was trying to scan modules but no change ...

Thanks.

M.

Alfaeddy
Posts: 1350
Joined: 19 Feb 2011, 17:43
Location: Germany , Aarbergen

Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)

Post by Alfaeddy » 04 Aug 2013, 09:25

aaa456 wrote:Hi Alfaeddy,

yes, that's how it is connected. I was wrong, adapter is connected correctly (I was probably looking on it upside down :oops: ). Except one difference. According the scheme pins 4 and 5 should be connected together (short-circuit) but in my adapter they are just connected 4-4 and 5-5 (and not between pins). But maybe this is not a problem ...

Code: Select all

Hello M.

Right, pins 4 & 5 are not a problem because both pins are competent for the mass
 
And the pin 16 for the power supply interface is! Is this so? on your Adpter?

otherwise I would not remember where your connection error

Greetings Eddy
So I really don't know where could be a problem ... :-( It's true that ELM interface connected directly to OBD in car is tighter than adapter (very loose). I tried to push it and hold it while I was trying to scan modules but no change ...

Thanks.

M.

aaa456
Posts: 6
Joined: 28 Jul 2013, 18:41

Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)

Post by aaa456 » 04 Aug 2013, 20:40

Hi Alfaeddy,

yes, pin 16 is connected correctly (pin 16 to pin 16). I have to check it even more deeper ....

Thanks.

M.

yoko
Posts: 11
Joined: 17 Aug 2012, 22:07

Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)

Post by yoko » 07 Aug 2013, 11:51

I removed the resistance as shown but i still can't get more than the engine when i scan
IMG_2464.JPG
IMG_2464.JPG (179.73 KiB) Viewed 4648 times

Alfaeddy
Posts: 1350
Joined: 19 Feb 2011, 17:43
Location: Germany , Aarbergen

Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)

Post by Alfaeddy » 07 Aug 2013, 13:25

Hallo Yoko

Du hast unterschiedliche ELM Interface ??? ein blaues und dann ein schwarzes

Dann auch verschiedene Autos ?? Linea und Grande Punto

Der Linea hat für ECU , ABS keinen CAN Bus , daher kann der Brückenwiderstand nicht der Fehler sein
Für das ABS benötigst du den Adapter A1

Die anderen Steuerungen werden über CAN Bus gelesen , bei denen kann es der Brückenwiderstand sein der Probleme macht

Dann einen Grande Punto , bei diesem werden alle Steuerungen über CAN Bus gelesen
für alle Steuerungen außer ECU , Lenkung und ABS wird der Adpter A3 benötigt.

Ich denke du solltest mal mit diesem Treiber versuchen.

http://www.ftdichip.com/Drivers/VCP.htm

Und überprüfe noch mal die Einstellungen und stelle die Wartezeit der COM ports auf 1 (statt 16)

Gruß Eddy

yoko
Posts: 11
Joined: 17 Aug 2012, 22:07

Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)

Post by yoko » 07 Aug 2013, 15:00

the first elm was borrowed from a friend then i bought one because i didn't want to open his interface
my car is a linea not a grande punto
i will update my drivers and will let you know

btw i can't read German

Greatjoe
Posts: 4
Joined: 08 Aug 2013, 11:00

Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)

Post by Greatjoe » 08 Aug 2013, 11:18

Hi,

I have tried looking for my ELM 327 bluetooth module on this tread but can't seem to find it (The thread is so long now).

Here are photos of the adaptor, Does anyone know what resistor I need to remove on this in order to access the body computer?

Thanks
Attachments
rsz_dsc_0167.jpg
rsz_dsc_0167.jpg (166.91 KiB) Viewed 4635 times
rsz_dsc_0166.jpg
rsz_dsc_0166.jpg (178.23 KiB) Viewed 4635 times
rsz_1rsz_1rsz_dsc_0168.jpg
rsz_1rsz_1rsz_dsc_0168.jpg (32.08 KiB) Viewed 4635 times

Post Reply