elm 327 1,4a timeout...

multiecuscan program usage help
Post Reply
spider99
Posts: 5
Joined: 20 Jun 2010, 08:30

elm 327 1,4a timeout...

Post by spider99 » 08 Sep 2010, 20:01

Code: Select all

http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=300464930130&ssPageName=ADME:X:AAQ:GB:1123#ht_6701wt_1137
its not working conection time out please help?
Do i need the car power for the test ( test buton in setup)

Tipiak
Posts: 7
Joined: 26 Dec 2009, 22:07

Re: elm 327 1,4a timeout...

Post by Tipiak » 11 Sep 2010, 20:04

Same problem here with ELM327 1.4a, test in settings works fine. I don't have a timeout but i says to check my cable

While with KKl cable, it works fine

Tipiak
Posts: 7
Joined: 26 Dec 2009, 22:07

Re: elm 327 1,4a timeout...

Post by Tipiak » 11 Sep 2010, 20:09

Image

spider99
Posts: 5
Joined: 20 Jun 2010, 08:30

@ Yani

Post by spider99 » 19 Oct 2010, 21:24

Today test. all ok.
ebay seller is ok.
christianttjones

http://cgi.ebay.co.uk/ELM-327-USB-1-4a- ... 119wt_1139

Today I bought and tested the program with this cable works perfectly. (and the kkl)

@ Yani,
1 question I have here an Alfa GT jtd of 2005 with 202,000 on the clock but the odo in the software gives 1.799.6 km? Software 2002 is also strange
What is the cause?
Please comment.

Yani thanks for this wonderful program.

sprint750
Posts: 4
Joined: 01 Oct 2010, 23:51

Re: elm 327 1,4a timeout...

Post by sprint750 » 23 Oct 2010, 00:05

Bought also my interface from him. (1.4 working fine !!)
Everything was great. Very professional seller.

Regards
Sébastien
A pessimistic is a former optimistic who gathered experience

Psychik
Posts: 6
Joined: 31 Aug 2010, 19:23

Re: elm 327 1,4a timeout...

Post by Psychik » 23 Oct 2010, 09:04

i have bought ELM 327 1.4+ as on picture downside. :mrgreen:
this device was alredy modified for Fiat. there were changes like on picture below.
i check resistor and they were 100 Ohm both. i have no multimeter to check capacitors.

but there was a problem. each time i plug this interface into my car (Punto HGT 1.8 16V Faza3) i receive errors in main computer and CAN bus transmision stuck until i remove elm327 and restart power from key.
also there was a lot of unnecesary lights, gasoline-meter light was blinking and shows no gas.

Image

i decide to broke into elm and remove this additional parts like this:

Image

now everything works fine in my car. i have to test this ELM with other fiat's. :)

sebfri
Posts: 12
Joined: 29 Oct 2010, 20:58

Re: elm 327 1,4a timeout...

Post by sebfri » 10 Nov 2010, 17:54

sprint750 wrote:Bought also my interface from him. (1.4 working fine !!)
Everything was great. Very professional seller.

Regards
Sébastien
I bought ELM 327 by christianttjones in eBay, that's work for engine but doesn't work in service maintenance reset.

Do you try it in service reset ?

alfa156sarajevo
Posts: 870
Joined: 12 Feb 2010, 09:03
Location: EU, Germany

Re: elm 327 1,4a timeout...

Post by alfa156sarajevo » 18 Nov 2010, 12:13

sebfri wrote:
sprint750 wrote:Bought also my interface from him. (1.4 working fine !!)
Everything was great. Very professional seller.
Regards
Sébastien
I bought ELM 327 by christianttjones in eBay, that's work for engine but doesn't work in service maintenance reset.
Do you try it in service reset ?
sebfri
do you have REGISTERED version of FES?
Coded Keys & CODE card for Alfa Romeo, Fiat and Lancia cars

sebfri
Posts: 12
Joined: 29 Oct 2010, 20:58

Re: elm 327 1,4a timeout...

Post by sebfri » 18 Nov 2010, 23:38

Yes of course !!!

Post Reply