FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)

multiecuscan program usage help
scarface53
Posts: 1
Joined: 28 Dec 2019, 09:23

Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)

Post by scarface53 » 28 Dec 2019, 09:26

hello,I bought vgate icar 2 wifi version
the board is that,but I can't connect to multiecuscan body,proxyaligment etc,only engine, I can't find 121 resistor,can you help me? thank you

https://i.postimg.cc/bNjDkV0n/IMG-20191228-020357.jpg
https://i.postimg.cc/MTCcsdhh/IMG-20191228-020402.jpg

handynoturno
Posts: 1
Joined: 09 Jan 2020, 13:31

Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)

Post by handynoturno » 09 Jan 2020, 13:55

Guys, first make sure that the interface used is actually implemented with the 121ohms resistor


check below:
https://www.youtube.com/watch?v=emzyE-zkGmw


resistor that must be removed:
https://ibb.co/tczXLW2

After checking that between pins 6 and 14
is showing 120 ohms on the multimeter, look for it on the board and remove it


Sorry my bad english.

Mark1
Posts: 1
Joined: 29 Jan 2020, 11:40

Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)

Post by Mark1 » 29 Jan 2020, 12:04

Hello everyone!
I have read and experimented a lot with the best value for money tool.
So far I have come to this tool: https://www.aliexpress.com/item/32862479065.html?spm=a2g0s.9042311.0.0.5d824c4dJTLVmL

I've tested many of the same looks, both old and new, and foror at similar prices , ONLY this device seems to be good.

(So far I've only tested it with key programming radio and immo)

I hope I help with it, so I wrote this so that everyone doesn't buy as much cheap equipment as I do.

BR.

Image

ivanov156
Posts: 1
Joined: 03 Feb 2020, 22:30

Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)

Post by ivanov156 » 03 Feb 2020, 22:46

Mark1 wrote:
29 Jan 2020, 12:04
Hello everyone!
I have read and experimented a lot with the best value for money tool.
So far I have come to this tool: https://www.aliexpress.com/item/32862479065.html?spm=a2g0s.9042311.0.0.5d824c4dJTLVmL

I've tested many of the same looks, both old and new, and foror at similar prices , ONLY this device seems to be good.

(So far I've only tested it with key programming radio and immo)

I hope I help with it, so I wrote this so that everyone doesn't buy as much cheap equipment as I do.

BR.

Image
Hi,

I have the same cable as yours. I have MES 3.6 cracked and working fine with VAG COM cable. To be able to connect to the Delphi electric power steering of my Punto MK2 i need the ELM 327. When i adjust the port settings from the device manager (using FTDI virtual com port) but when i try to connect MES cant find the com port, or in some cases the error is SUITABLE INTERFACE NOT FOUND. I need to mention that i did not installed anything before try to use the ELM327 cable (the small disc with the cable was damaged). Someone can help?

s130
Posts: 656
Joined: 20 Jan 2010, 10:07
Location: Southampton, United Kigndom
Contact:

Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)

Post by s130 » 04 Feb 2020, 12:21

ivanov156 wrote:
03 Feb 2020, 22:46

Hi,

I have the same cable as yours. I have MES 3.6 cracked and working fine with VAG COM cable. To be able to connect to the Delphi electric power steering of my Punto MK2 i need the ELM 327. When i adjust the port settings from the device manager (using FTDI virtual com port) but when i try to connect MES cant find the com port, or in some cases the error is SUITABLE INTERFACE NOT FOUND. I need to mention that i did not installed anything before try to use the ELM327 cable (the small disc with the cable was damaged). Someone can help?
Please do not expect official help as I bring your attention to this site's official statement:

"PLEASE NOTE: Our email is flooded with complaints for incorrect operation and virus problems from people who use manipulated copies of Multiecuscan (bought from Chinese web sites and elsewhere). We cannot take any responsibility for incorrect operation of non-genuine software and the problems it may cause to your computer and vehicle. We will not reply to any email from users of this software and will not provide any support to them.
The genuine software has digital signature and can be downloaded from this web site. Licenses for the software can be purchased from here or from one of the distributors."
Fiat Strada/Ritmo Abarth 130TC, Barchetta 2005 , 500X Cross Plus

GeorgeSmyrlis
Posts: 1
Joined: 10 Feb 2020, 18:14

Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)

Post by GeorgeSmyrlis » 10 Feb 2020, 19:17

Hello guys, i have bought the MES (50€ licence) and i have the elm327 diag on photos. I connnect to engine on Punto mk2 just fine and i have all the tests OK but i cannot connect to bcm or dashboard to make proxi alignement, It gives me canbus error. Can someone help me on what resistors or something else i need to change to make it work? Thanks, George from greece.

<blockquote class="imgur-embed-pub" lang="en" data-id="a/I6uN7fa"><a href="//imgur.com/a/I6uN7fa"></a></blockquote><script async src="//s.imgur.com/min/embed.js" charset="utf-8"></script>

Post Reply