Help with Errors found: B10AA-4A - Control configuration PROXI

multiecuscan program usage help
Post Reply
iCabido
Posts: 15
Joined: 15 Feb 2018, 17:59

Help with Errors found: B10AA-4A - Control configuration PROXI

Post by iCabido » 27 May 2019, 11:08

Hello, someone can help me with Errors found: B10AA-4A - Control configuration PROXI? When I relate the alignment I get that error and I can not finish the alignment or while I do almost all the elements are out of time.
What may be happening? It had never happened to me before in the same vehicle.

s130
Posts: 608
Joined: 20 Jan 2010, 10:07
Location: Southampton, United Kigndom
Contact:

Re: Help with Errors found: B10AA-4A - Control configuration PROXI

Post by s130 » 27 May 2019, 15:47

From the Fiat 500X Service Manual:

334- 500X - Check Configuration Failed -Incorrect component installed B10AA-4A

If you are doing a Custom Proxy Data load then the data you are trying to load may be incorrect.

Also found this info:

https://chrysler.oemdtc.com/tag/b10aa

https://www.obd-data.com/b10aa.html

Have you tried clearing the B10AA fault. Turning the ignition off. Turning the ignition on and checking for the DTC again? If clear try the Proxy again.
Fiat Strada/Ritmo Abarth 130TC, Barchetta 2005 , 500X Cross Plus

iCabido
Posts: 15
Joined: 15 Feb 2018, 17:59

Re: Help with Errors found: B10AA-4A - Control configuration PROXI

Post by iCabido » 02 Jun 2019, 14:46

Thank you for responding and you answered, it has been helpful.
Now I can do proxy alignment and everything goes ok.
But I get the following errors:
Errors found:
B1040-64
B1033-64
U2066-87
U2055-87
U2054-87
Do you know how I can solve it? I have deleted it but it will come back, I understand that it is referring to uconncet 6.5 "The vehicle is the same as always and no new things have been installed.

s130
Posts: 608
Joined: 20 Jan 2010, 10:07
Location: Southampton, United Kigndom
Contact:

Re: Help with Errors found: B10AA-4A - Control configuration PROXI

Post by s130 » 02 Jun 2019, 16:57

B1040-64 = Radio_Frequency_Hub_Module(FULL)_Continental\ --> Operational Mode Status info 1 - Signal plausibility failure B1040-64
B1033-64 = Radio_Frequency_Hub_Module(FULL)_Continental\ --> Operational Mode Status 1 - Signal plausibility failure B1033-64
U2066-87 - I have no information
U2055-87 = Radio_Frequency_Hub_Module(FULL)_Continental\ --> BCM_COMMAND message 3 - Missing message U2055-87
U2054-87 = Radio_Frequency_Hub_Module(FULL)_Continental\ --> BCM_COMMAND message 2 - Missing message U2054-87

So for some reason the vehicle is not happy with uConnect/Radio set-up.

If you delete the errors AND DO NOT attempt a PROXI again then

1) Does your uConnect work OK?
2) After several vehicle start/stop cycles do the errors re-appear?
3) Is your odometer NOT flashing which would indicating there IS NOT PROXi issue?

If the answers are:

1) YES
2) NO
3) YES

Then I would just not worry and ignore. It is not uncommon for vehicles to show have unexplained error codes appearing.

I would add that when multiple different errors occur then this is often an indication of poor battery power, poor main electrical connections especially the main vehicle earth/negative connection.
Fiat Strada/Ritmo Abarth 130TC, Barchetta 2005 , 500X Cross Plus

Post Reply