Multiecuscan

Hello to everybody,
I have an alfa 159 1.9 JTDm 8v with multiscan regular license, but when i try to work on it, it give me access only to the engine ecu! for all other ecu it says:
"ELM 327-> ECU connection failed!"
how can i fix it? if i check all the cu, it finds me only the engine.
Thank you!

Regular license means registered?
Did you try the Adapter Cable A1?

no because before buy other cables i will like to know if it's a problem of software or something else, in theory in supported vehicles, my car doesn't need any special cables:
Bosch EDC16C39 CF4/EOBD Diesel Injection (1.9, 2.4) |INFO|DTC|DTC EX|PRM|ACT|ADJ| KLELMOBDKey
AISIN AF40-6 Automatic Gearbox |INFO|DTC|DTC EX|PRM|ACT|ADJ| KLELMOBDKey
TRW Lucas ABS |INFO|DTC|PRM|ACT| KL 1ELM 1OBDKey 1 A1
TRW Lucas ABS (ESP) |INFO|DTC|PRM|ACT|ADJ| KL 1ELM 1OBDKey 1 A1
TRW MY03 Airbag (2F-2P-2L-2T-1G-I) |INFO|DTC|DTC EX|PRM|ACT| ELMOBDKey
TRW MY03 Airbag (2F-2P-2L-2T-2G-I) |INFO|DTC|DTC EX|PRM|ACT| ELMOBDKey
Steering Lock TRW |INFO|DTC| ELMOBDKey
Service Interval Reset (Siemens) |INFO|ADJ| ELMOBDKey
Connect (NAV) Marelli |INFO|DTC|PRM|ACT|ADJ| ELMOBDKey
Convergence Lauberhorn C1 (Blue&Me Nav) |INFO|DTC| ELMOBDKey
Convergence Marelli/Microsoft (Blue&Me) |INFO|DTC| ELMOBDKey
Convergence Marelli/Microsoft C3 (Blue&Me Nav) |INFO|DTC| ELMOBDKey
Instrument Panel Siemens |INFO|DTC|PRM|ACT|ADJ| ELMOBDKey
Body Computer Marelli (939) |INFO|DTC|DTC EX|PRM|ACT|ADJ| ELMOBDKey
CAN Info |INFO| ELMOBDKey
CAN Monitor / Vehicle Settings |DTC|PRM|ADJ|
CAN Setup / PROXI Alignment Procedure |INFO|ADJ| ELMOBDKey
TEG Reader TRW (Electronic key) |INFO|DTC|DTC EX|PRM|ACT|ADJ| ELMOBDKey
Delphi climate control (Dual/three zone) |INFO|DTC|PRM|ACT| ELMOBDKey
Delphi climate control (Single zone) |INFO|DTC|PRM|ACT| ELMOBDKey
Litronic XENON headlamp (left) |INFO|DTC|PRM|ACT|ADJ| KL 12ELM 12OBDKey 12 A1
Litronic XENON headlamp (right) |INFO|DTC|PRM|ACT| KL 12ELM 12OBDKey 12 A1
Boot G.E. PROCOND |INFO|DTC|PRM|ACT| ELMOBDKey
Driver's Door G.E. PROCOND |INFO|DTC|PRM|ACT| ELMOBDKey
Driver's Seat LEAR |INFO|DTC| ELMOBDKey
Front Doors G.E. PROCOND |INFO|DTC|PRM|ACT| ELMOBDKey
Parking Control VALEO |INFO|DTC|PRM|ADJ| ELMOBDKey
Passenger's Door G.E. PROCOND |INFO|DTC|PRM|ACT| ELMOBDKey
Passenger's Seat LEAR |INFO|DTC| ELMOBDKey

1) Well, for some modules your car NEEDS A1
2) The free version only reads Engine and CAN info
3) Any other doubts?

thank for your kind answer:
1) i have a registered version
2) i need to reset service message but it gives me the failed connection.
Have i to buy the adapter cable even for the service? because i read that elm 327 was enough but maybe i'm wrong

No, maybe you should remove the resistor... viewtopic.php?f=5&t=1493

I haven't any ideas about how to do the work, can you please link a site where i could buy the right cable please?:)

No, sorry...

Hello, i suppose the problem was in the clabe, i ordered a new one and we it will arrive i will update you if it works or not

Unfortunetly he didn't update. Probably it works now