Search found 825 matches
- 27 Oct 2016, 08:31
- Forum: General
- Topic: Multiecuscan 3.3 Released!
- Replies: 0
- Views: 7695
Multiecuscan 3.3 Released!
On 15/10/2016 - Multiecuscan 3.3 was released - Added support for Ducato x290 - Added support for Idea 1.8 16V (Brazil) - Support for Marelli 9DF CF6/EOBD Diesel Injection (1.3) (500L, Panda, Punto, Mito) - Support for Bosch Marelli 8F3 CF5/CF5+/EOBD Diesel Injection (2.3) (Fiorino, Qubo) - Support ...
- 12 Oct 2016, 14:51
- Forum: Usage Q&A
- Topic: advice needed on upgrading my current multiecuscan
- Replies: 1
- Views: 2121
Re: advice needed on upgrading my current multiecuscan
Check out one of these authorised distributors: http://www.multiecuscan.net/Distributors.aspx Unless you go for the multiplexed interface (http://www.multiecuscan.net/OrderMultiplexed.aspx) then you will need a KKL Interface, ELM interface and a full set of EOBD adaptor cables. In addition if you ar...
- 29 Sep 2016, 18:32
- Forum: General
- Topic: Electronuc security code
- Replies: 8
- Views: 6088
Re: Electronuc security code
Where are you located Marqo? Which country?marqo wrote:I have the same - I'm own 500X but without the security code.
Have you been told by a Fiat Dealer/Service agent that the code is not available and only delivered directly to authorise diagnostic equipment with a "live" connection to Fiat's servers?
- 27 Sep 2016, 18:23
- Forum: General
- Topic: Electronuc security code
- Replies: 8
- Views: 6088
Re: Electronuc security code
So you have the code but it cost. :evil: A long time ago made it a condition of new vehicle purchase that I have all the codes. This has worked very well until my new 500X where I found out that whilst mechanical key code and radio code are available with the car but the security code is only delive...
- 26 Sep 2016, 09:50
- Forum: General
- Topic: Electronuc security code
- Replies: 8
- Views: 6088
Re: Electronuc security code
Well yes it is bad and I have ha a long discussion with Fiat UK a few years ago about this. They claim security etc. etc. I pointed out to them that their security points were, whilst well meant, totally wide of the mark for several reason, some listed below. 1) I applied via my Fiat dealer. I had t...
- 24 Sep 2016, 18:17
- Forum: General
- Topic: Electronuc security code
- Replies: 8
- Views: 6088
Re: Electronuc security code
Typical British / FIAT UK practice. Firstly, as far as I know the only MES functions that require a body computer code are 1) key programming and 2) alarm/security settings. A proxy alignment does not require a security code however after the alignment the alarm/security settings will be set to thei...
- 22 Sep 2016, 15:43
- Forum: Usage Q&A
- Topic: MultiEcuScan won't work on my Panda
- Replies: 3
- Views: 3982
Re: MultiEcuScan won't work on my Panda
A Panda bought new in 2008 is most probably the Panda '03 as far as MES is concerned. Only way to confirm/deny this is by your chassis number. Unless you have the TRW Airbag 2 (Ep - PROXI) air bag computer which is a CAN Bus device you will need a KL connection/interface with KL3 adaptor cable. If M...
- 31 Jul 2016, 16:55
- Forum: Bugs
- Topic: Internal Error-graph from other PC-decimal separator issue
- Replies: 2
- Views: 3594
Re: Internal Error-graph from other PC-decimal separator iss
International language support, code pages, decimal "." vs "," separators are a real pain to code and test (I speak from limited experience )
- 28 Jul 2016, 09:39
- Forum: General
- Topic: Alfa 147 selespeed with AutoDia E327
- Replies: 2
- Views: 2899
Re: Alfa 147 selespeed with AutoDia E327
I think you will find the answers to your questions here: http://www.multiecuscan.net/SupportedVehiclesList.aspx For the 147 Selespeed you will see that the Engine, ABS, Gearbox, Service reset and Airbag system can be connected to with the free version of MES. All other systems (list is red) require...
- 25 Jul 2016, 07:58
- Forum: General
- Topic: Best equipment to reset Qubo Service Light
- Replies: 1
- Views: 2209
Re: Best equipment to reset Qubo Service Light
If you want guaranteed to work hardware for MES then look here: http://www.multiecuscan.net/Distributors.aspx
You can buy cheaper kit but as you have found out it may not work.
You can buy cheaper kit but as you have found out it may not work.