Search found 30 matches
- 21 Jan 2019, 20:46
- Forum: Usage Q&A
- Topic: Can't connect via Bluetooth ELM327
- Replies: 4
- Views: 5062
Re: Can't connect via Bluetooth ELM327
Try connrcting to the module you found, the engine. Then switch to the faults tab to read the fault. Or just scan DTC. But that's not really important, the ELM you have is 99% faulty, but can be "repaired". You have to open the case and remove the 120 ohm resistor. To be sure before opening, measure...
- 21 Jan 2019, 19:34
- Forum: Usage Q&A
- Topic: Same ECU listed multiple times in supported vehicles, free AND registered only, difference?
- Replies: 1
- Views: 1708
Re: Same ECU listed multiple times in supported vehicles, free AND registered only, difference?
Not exactly the same ECUs. The two free versions are also different, mainly in their ISO numbers.
The one that only the registrated version can handle is type 59F, while the other two can be other types also.
The differences are in EURO2/3/4 regulations, and related stuff.
The one that only the registrated version can handle is type 59F, while the other two can be other types also.
The differences are in EURO2/3/4 regulations, and related stuff.
- 21 Jan 2019, 19:26
- Forum: Usage Q&A
- Topic: GRANDE PUNTO,PUNTO 03 COMMUNICATION PROBLEM
- Replies: 1
- Views: 1216
Re: GRANDE PUNTO,PUNTO 03 COMMUNICATION PROBLEM
You need an A3 adapter for certain modules, not a 3 pin adapter. Check the Supported Vehicles page, and the adapter diagram below:
- 21 Jan 2019, 19:16
- Forum: Usage Q&A
- Topic: High sampling time - Punto mk2 ECU
- Replies: 1
- Views: 952
Re: High sampling time - Punto mk2 ECU
Any ideas? I'd pleased also if anyone would share usage experience about reading live parameters, what is the normal delay between two data readout.
- 21 Jan 2019, 19:02
- Forum: Usage Q&A
- Topic: Can't connect via Bluetooth ELM327
- Replies: 4
- Views: 5062
Re: Can't connect via Bluetooth ELM327
A bad CAN termination resistor causes this symptom. I guess there is a CAN bus fault stored in the ECU if you connect and read it out.
You can read more about this in the faulty elm interfaces demystified topuc. Try to disassemble and post high quality photos of the internal board.
You can read more about this in the faulty elm interfaces demystified topuc. Try to disassemble and post high quality photos of the internal board.
- 21 Jan 2019, 18:57
- Forum: Usage Q&A
- Topic: Vagkkl interface.
- Replies: 18
- Views: 6873
Re: Vagkkl interface.
Post a screenshot of your Multiecuscan interface settings and one screenshot of your Windows device manager, Ports category opened. Also, a screenshot of your current interface driver could help. Or simply update your driver to the latest. Is this the same interface you used successfully a few years...
- 19 Jan 2019, 17:52
- Forum: Usage Q&A
- Topic: punto 1.2 8v petrol - ecu adaptiv reset
- Replies: 9
- Views: 4101
Re: punto 1.2 8v petrol - ecu adaptiv reset
Any fault codes stored?
The described method should work...
The described method should work...
- 15 Jan 2019, 19:53
- Forum: Usage Q&A
- Topic: High sampling time - Punto mk2 ECU
- Replies: 1
- Views: 952
High sampling time - Punto mk2 ECU
Hello, I'm experiencing high sampling time when reading (and recording) parameters from the ECU of my Punto mk2 1.2 16V. I'm trying to read out live data for troubleshooting, but data is collected only every 2-3 seconds or more if I select a number of paramters. I'm using an ELM327 1.4, capable of H...
- 20 Jun 2018, 20:55
- Forum: General
- Topic: PROXI Alignment sequence order
- Replies: 2
- Views: 2188
Re: PROXI Alignment sequence order
Well, I have one dashboard with all LEDs in it (almost.. it doesn't have the automatic gearbox led), but still having the NQS error and doesn't writing to other nodes.
- 20 Jun 2018, 20:49
- Forum: General
- Topic: Proxy alignment options removed in new versions - Fiat Punto
- Replies: 0
- Views: 1167
Proxy alignment options removed in new versions - Fiat Punto
Hi, I noticed that some Adjustment options in the CAN Setup menu are removed for Fiat Punto '03 1.2 16V (maybe for other variants too). In version 3.6, there were two options, to set ABS System Prensent/Not Present and set Speed Sensor type. In version 4.0 and above (at least I noticed in this versi...