Search found 30 matches

by kido.resuri
16 Oct 2019, 17:50
Forum: Usage Q&A
Topic: ELM327 - Why doesn't it support KKL?
Replies: 1
Views: 3160

ELM327 - Why doesn't it support KKL?

As in the topic. As far as I know, certain airbag, ABS modules communicate on K-Line protocol, connected to specific OBD2 pins. K-line is ISO 9141. ELM327 seems to support ISO 9141, and certain interfaces do have connected pins on pin 7 of it's OBD connector. What is the reason for that Multiecuscan...
by kido.resuri
25 Mar 2019, 21:29
Forum: General
Topic: Programming Transponder/Remote Control for Fiat Grande Punto 2006
Replies: 6
Views: 10076

Re: Programming Transponder/Remote Control for Fiat Grande Punto 2006

You need the dump of the body controller and a key programmer device, like zed-bull to prepare an id48 chip, so you can program it to.the car with multiecuscan.
by kido.resuri
03 Feb 2019, 07:52
Forum: Bugs
Topic: ECU Comunication Failed | ELM327 USB 1.5
Replies: 3
Views: 4357

Re: ECU Comunication Failed | ELM327 USB 1.5

You probably have a fake elm, or you did not switch the ignition on.

To which module and what car did you try to connect?

For more help, you need to post more details of your interface and the whole Test results.
by kido.resuri
24 Jan 2019, 21:20
Forum: Usage Q&A
Topic: punto 1.2 8v petrol - ecu adaptiv reset
Replies: 9
Views: 3911

Re: punto 1.2 8v petrol - ecu adaptiv reset

Do you have the logs folder setup correctly? If so, try posting some logs about the reset.
by kido.resuri
24 Jan 2019, 18:23
Forum: Usage Q&A
Topic: punto 1.2 8v petrol - ecu adaptiv reset
Replies: 9
Views: 3911

Re: punto 1.2 8v petrol - ecu adaptiv reset

Did you experience any misbehaviour before you did the self adaptation and phonic wheel reset? Try doing the resets again. Are you using registered version of Multiecuscan? Try contacting yani, he may ask you to send the report after the resets (the big red send report button in the main menu near t...
by kido.resuri
23 Jan 2019, 21:01
Forum: Usage Q&A
Topic: failed connection can bus
Replies: 3
Views: 4755

Re: failed connection can bus

Probably your interface is a fake elm. Resistor-related faults show the interface compatible, but can't connect to anything else than the engine ECU. You can test your interface with an ELM compatibility tester software, that will show you which versions - if any - does your interface support. https...
by kido.resuri
22 Jan 2019, 21:07
Forum: Usage Q&A
Topic: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)
Replies: 2535
Views: 3924850

Re: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE)

Probably your interface is a fake elm. Resistor-related faults show the interface compatible, but can't connect to anything else than the engine ECU. You can test your interface with an ELM compatibility tester software, that will show you which versions - if any - does your interface support. https...
by kido.resuri
22 Jan 2019, 20:50
Forum: Usage Q&A
Topic: Vagkkl interface.
Replies: 18
Views: 6602

Re: Vagkkl interface.

Try this driver:

https://www.ftdichip.com/Drivers/CDM/CDM21228_Setup.zip


Do you have a hardware COM port on your laptop?
by kido.resuri
21 Jan 2019, 20:54
Forum: Usage Q&A
Topic: Failed to connect to Body Computer
Replies: 2
Views: 4229

Re: Failed to connect to Body Computer

Usually if you can connect to the engine but not other modules, than your ELM has bad termination resistor on CAN line. After removing (and even better: adding proper termination), it should work. Only if you have FTDI USB IC in it and PIC microcontroller. Cheap fake chinese clones are totally usele...