Search found 23 matches

by oem
13 May 2013, 20:50
Forum: Usage Q&A
Topic: TRA and FRA self adaptive
Replies: 2
Views: 3787

Re: TRA and FRA self adaptive

You have rich mixtures on lpg. The best choice is reset adaptation. Driving on petrol for 10 km at part throttle (up to 80% throttle). Working at idle for 15 min on >80C engine temperature.

Look adaptation values and then adjust lpg with keep the same values.
by oem
26 Dec 2012, 08:08
Forum: General
Topic: Multiecuscan 1.2 RELEASED!
Replies: 11
Views: 8595

Re: Multiecuscan 1.2 RELEASED!

Big Update! :D I always wanted the "map generator" and i can't wait to test it out :D If you can fix the EGT function on bosch me7.9.10 introduced few versions ago...not displaying any value, a zero neither, would be great :P thank for your hard work!! Please note that the MAP is not accurate and w...
by oem
20 Feb 2012, 09:38
Forum: General
Topic: CANtieCAR 2.0
Replies: 1
Views: 2118

Re: CANtieCAR 2.0

230 EUR for new customer (inc. FES Multiplexed license)
190 EUR for current customer (inc. FES Multiplexed license)
by oem
06 Jul 2010, 12:16
Forum: Usage Q&A
Topic: running diagnostic on free rev - Alfa GT
Replies: 3
Views: 2490

Re: running diagnostic on free rev - Alfa GT

Yes, you can. You must see the Air Quantity in real time. Air Quantity on 7000 rpm must be 408 kg/h
by oem
06 Jul 2010, 06:24
Forum: Usage Q&A
Topic: running diagnostic on free rev - Alfa GT
Replies: 3
Views: 2490

Re: running diagnostic on free rev - Alfa GT

When the engine is at maximum speed (rpm limiter and full throttle), maf sensor should consider 408 kg / h air.
by oem
28 Jun 2010, 09:50
Forum: Usage Q&A
Topic: Upgrade ELM327 v1.2 (fake 1.5a) from 9600bps to 34800bps
Replies: 15
Views: 29137

Re: Upgrade ELM327 v1.2 (fake 1.5a) from 9600bps to 34800bps

So, does it work only on 1.2 version? Because i have the 1.3a clone that works great. It seems to be the same of plastic one in your pictures.... I use a couple of softwares where i can choose bps rate and if i choose an higher value instead of 9600 it still works fine. But i have an application th...
by oem
27 Jun 2010, 13:15
Forum: Usage Q&A
Topic: Upgrade ELM327 v1.2 (fake 1.5a) from 9600bps to 34800bps
Replies: 15
Views: 29137

Re: Upgrade ELM327 v1.2 (fake 1.5a) from 9600bps to 34800bps

I use it and no problems. I took the idea from another forum where they describe in detail the operation and say it works and no problem.
by oem
27 Jun 2010, 09:20
Forum: Usage Q&A
Topic: Upgrade ELM327 v1.2 (fake 1.5a) from 9600bps to 34800bps
Replies: 15
Views: 29137

Re: Upgrade ELM327 v1.2 (fake 1.5a) from 9600bps to 34800bps

There is a difference in the CAN protocol. There ECU support at higher speeds.

Should not have a damage control unit or ELM. However, do it at your own risk!

For me, this modification was necessary in consequence of the use of some other software the connection with CAN-BUS and using this ELM327.
by oem
26 Jun 2010, 15:36
Forum: Usage Q&A
Topic: Upgrade ELM327 v1.2 (fake 1.5a) from 9600bps to 34800bps
Replies: 15
Views: 29137

Re: Upgrade ELM327 v1.2 (fake 1.5a) from 9600bps to 34800bps

No, no connect pin 6 from OBD connector. Pin 6 from Microchip to 5v. and remove/unsolder resistor R24 from sheme. Is this :) When this manipulation try to connect with 34800 boud. :)
by oem
25 Jun 2010, 22:30
Forum: Usage Q&A
Topic: Upgrade ELM327 v1.2 (fake 1.5a) from 9600bps to 34800bps
Replies: 15
Views: 29137

Re: Upgrade ELM327 v1.2 (fake 1.5a) from 9600bps to 34800bps

I edit the post. In first post is ELM327 1.2 (1.5 fake version). Now, here is the plastic ELM interface.